Glass of wine on a marble table, a common cause of etching rings and stains on natural stone

Marble Etching vs Staining: How to Tell the Difference and Fix Both

The short answer

If a mark on your marble feels rough or looks dull, it's etching: acid has worn away the polished surface. If it's darker or coloured but still feels smooth, it's a stain: something has soaked into the stone. Etching is fixed by re-polishing the surface. A stain is drawn out with a poultice. Get the diagnosis wrong and neither fix will work.

That ring under last night's wine glass, the dull patch beside the basin, the shadow where a candle sat on the coffee table: almost every mark on marble is one of these two things. Natural stone is meant to be lived with, and a mark is rarely the end of the world. You just have to know which one you're dealing with.

This guide covers how to tell them apart in 10 seconds, what causes each one around an Australian home, how to fix both, and how to stop them coming back. It applies to marble, travertine, limestone and onyx, which are all calcium-based stones and behave the same way.

 

What etching and staining actually are

Etching: a change to the surface

Marble is mostly calcium carbonate, and calcium carbonate reacts with acid. When something acidic touches the stone, it dissolves a microscopic layer of the polished face. What's left is a patch that has lost its shine. It might look cloudy, pale or matte, and it often feels slightly rough.

Nothing has been added to the stone, so there's nothing to clean off. Some of the surface is simply gone. That's why scrubbing an etch mark never helps, and why the fix is to restore the finish rather than lift anything out.

Staining: something soaked in

All natural stone is porous to some degree. Leave a liquid on it long enough and it can seep into those pores, carrying colour with it. Oil, coffee, red wine, ink, rust and even leaves on outdoor stone can all leave a mark this way.

The surface itself isn't damaged, so a stain feels as smooth as the stone around it. Because the colour is physically sitting inside the stone, it can usually be drawn back out.

Which stones are affected

Marble, travertine, limestone and onyx are all calcium-based, so all of them can etch and stain. Onyx is the most delicate of the four. Travertine's natural holes can trap liquid, so it needs a little extra care. Genuine quartzite is quartz-based and far more resistant to acid. Not every stone sold as quartzite is the real thing, though, so always ask before you buy.

Amara fluted round travertine dining table in warm beige travertine, a calcium-based stone that can etch and stain like marble

How to tell which one you have: the 10-second test

Clean the area with warm water and a drop of pH-neutral cleaner, dry it completely, then run these three checks.

  1. Look at it from a low angle. Crouch down until light bounces off the surface. An etch shows up as a dull or cloudy patch that breaks the reflection. A stain is a change in colour, and the shine across it looks the same as the rest of the stone.
  2. Feel it. Run a fingertip across the mark. If it feels slightly rough, dry or "grabby" compared with the stone around it, it's etching. If it feels just as smooth, it's a stain.
  3. Wet it. Put a few drops of water on the mark. An etch often seems to fade while it's wet and comes back as it dries. A stain stays the same colour whether it's wet or dry.

On a honed (matte) finish the low-angle check is harder, because there's no gloss to compare against. Rely on touch and colour instead.

Etching vs staining at a glance

Etching Staining
What it is Acid has dissolved part of the surface A liquid has soaked into the pores
Looks like Dull, cloudy, pale or matte patch; rings and drip marks Darker or coloured patch: brown, yellow, grey, orange, pink
Feels like Slightly rough or dry Smooth, same as the rest of the stone
When wet Often fades, then comes back when dry Stays visible
Common causes Citrus, wine, vinegar, soft drink, tomato, acidic cleaners Oil, coffee, red wine, ink, rust, cosmetics
Can it be undone? Yes, by re-polishing or honing the surface Usually, with a poultice
Does sealing help? No Yes, it slows absorption
What not to do Use a poultice or stronger cleaner Sand or polish the surface

Where marks usually come from, piece by piece

Every stone piece in your home sees different kinds of spills, so it helps to know what to watch for.

Piece Most likely etching from Most likely staining from
Dining tables Wine, citrus, salad dressing, tomato sauce, soft drink Olive oil, red wine left overnight, coffee, candle wax and dye
Coffee tables and side tables Glasses of wine, juice or cocktails with no coaster Coffee and tea rings, plant pots, metal objects that rust
Vanities and basins Bathroom sprays, toothpaste, mouthwash, perfume, limescale removers Makeup, hair dye, fake tan, hand cream, rust from cans
Bathtubs Acidic cleaners, bath bombs with citric acid, some bath products Bath oils, coloured salts, hair dye
Fireplaces Harsh soot cleaners Soot and smoke, scented candle oils
Outdoor stone Citrus drinks, pool water carried on wet feet Leaves and berries, bird droppings, sunscreen, BBQ fat

Cosmos Calacatta Viola marble dining table, a polished stone surface where wine and citrus spills can etch

A few marks catch people out:

  • White rings under glasses are nearly always etching from the drink rather than water, especially wine, gin and tonic, or anything with citrus.
  • Dull paths around the basin usually come from bathroom cleaners. Many "all-purpose" and limescale sprays are acidic.
  • Mystery dark patches that fade by the next day are just water that the stone has soaked up. Give it 24 to 48 hours to dry before you treat anything.

In a busy family home, a honed finish and a well-kept sealer will save you a lot of worry.

How to fix etching

Because etching is missing surface, the only real fix is to bring the finish back. How you do that depends on how deep the mark is and which finish your stone has.

Light etching on polished marble: try it yourself

This works for faint rings and small dull spots that you can see but barely feel.

  1. Clean and dry the area.
  2. Test a marble polishing powder or etch-remover cream on a hidden spot first, such as the underside edge of a tabletop.
  3. Dampen the area. Work a small amount of the product in with a soft cloth or felt pad, using firm circular strokes, for the time the label gives.
  4. Wipe it off, rinse with clean water, dry, and check from a low angle. Repeat once if needed.
  5. Reseal the area afterwards, because polishing can remove sealer.

Follow the product's safety instructions. Wear gloves, and never mix it with other cleaners.

On a honed (matte) finish: don't polish

Polishing powder will leave a shiny patch on honed stone, which can look worse than the etch did. Light etching on honed marble is often barely visible anyway. If it bothers you, a stone restorer can re-hone the area so the finish matches.

Deep or widespread etching: call a professional

If you can clearly feel the mark, or it covers a large area like a whole tabletop or a path around a basin, DIY products tend to leave a patchy shine. A stone restorer will hone the surface with progressively finer diamond pads, then polish it back to the original finish so the whole piece looks even.

What not to do

  • Don't use a poultice. There's nothing in the stone to draw out.
  • Don't scrub harder or reach for a stronger cleaner. Most strong cleaners are acidic or alkaline and will make the etching worse.
  • Don't use sandpaper or a rotary tool without training. It's easy to leave dips and swirl marks that cost more to fix than the original etch.

 

How to remove stains from marble

Stains come out of the stone; they aren't polished off. The tool is a poultice, a thick paste that soaks a chemical into the stain and then pulls the coloured residue up as it dries.

How to make and use a poultice

  1. Pick the absorbent. A ready-made stone poultice powder is easiest. Otherwise use diatomaceous earth, kaolin clay or plain white paper towels. Avoid coloured paper, which can bleed dye.
  2. Mix it with the right chemical for the stain (see the table below) until it's about as thick as peanut butter.
  3. Spread it about 5 to 6 mm thick, reaching a centimetre or two past the edge of the stain.
  4. Cover it with cling wrap, tape the edges down, and poke a few small holes so it dries slowly.
  5. Leave it 24 to 48 hours, until it's completely dry. The drying is what pulls the stain out.
  6. Lift it off with a plastic scraper or spatula, never metal. Rinse with clean water and dry.
  7. Repeat if needed. Old or deep stains can take three or four rounds. Once it's gone, reseal the area.

Always test on a hidden spot first, work with a window open, and never mix the chemicals with each other, or with other cleaners.

Which poultice for which stain

Stain Examples Mix the poultice with Notes
Oil-based Cooking oil, butter, hand cream, cosmetics Acetone or mineral turpentine Oil often darkens the stone from below. Be patient, it can take several rounds
Organic Coffee, tea, red wine, fruit, leaves, food Hydrogen peroxide (6 to 12 per cent, from a pharmacy or hair supplier) Peroxide can lighten dark stone. Only use it on white and light marble
Rust Metal pots, cans, furniture feet A rust remover made for natural stone Ordinary rust removers are acidic and will etch marble
Ink and dye Pens, hair dye, fake tan Light stone: hydrogen peroxide. Dark stone: acetone Act quickly. Dye sets the longer it sits
Water and mineral deposits Hard-water spots, white crusty build-up Usually no poultice needed Buff gently with dry, very fine (000 or 0000) steel wool
Candle wax Dining and coffee table centrepieces Not needed at first Harden the wax with ice, lift it with a plastic scraper, then use an oil-stain poultice for any mark left behind

When a stain won't budge

If three or four rounds haven't shifted it, the stain may be very deep, or it may have reacted with the stone. It's time to get a professional opinion before you try anything stronger.

 

When it's both, or neither

Etched and stained at the same time

Some spills do both. Red wine is acidic enough to etch and pigmented enough to stain, so it can leave a mark that's rough and pink at once. Coffee and tomato sauce can do the same.

Treat them in order:

  1. Remove the stain first with an organic-stain poultice, while the pores are still open.
  2. Once the colour has gone, deal with the etch by polishing (polished finish) or professional re-honing (honed finish).
  3. Reseal.

If you're unsure which part is which, get it looked at before you start.

Marks that aren't etching or staining

  • Scratches are fine lines from grit, ceramics or keys dragged across the top. Light ones on polished marble may buff out. Deeper ones need a professional.
  • Chips and cracks are physical damage, usually from a knock or uneven weight. Small chips can often be filled with a colour-matched resin by a stone repairer.
  • Darkening that disappears is trapped moisture. It dries out on its own within a day or two.
  • A cloudy or sticky film is usually built-up wax, soap or cleaner residue rather than damage. Clean it with a pH-neutral stone cleaner, then rinse and dry.
  • Yellowing on white marble can come from old wax or sealer, or from iron in the stone reacting to moisture. It's worth a professional look.

How to prevent etching and staining

Sealing helps with stains but does nothing for etching. Every other habit below helps with both.

Why sealing stops stains but not etching

A penetrating sealer sits inside the stone's pores and slows down how fast liquid soaks in. That buys you time to wipe up a spill before it stains. Acid doesn't need to get into the pores to do damage, though. It reacts with the surface itself, so even freshly sealed marble will etch if lemon juice sits on it.

We recommend resealing about every six months (see our Stone Care guide for suitable sealers). To check whether it's time, put a few drops of water on the stone and wait 10 to 15 minutes. If the stone darkens underneath, it's absorbing and needs resealing.

Everyday habits that make the biggest difference

  • Use coasters, placemats and trays. A marble tray under the bar cart, perfume bottles or bathroom products stops drips reaching the stone.
  • Wipe spills straight away. Blot, don't wipe, so you don't spread them. Be quickest with wine, citrus, oil and coffee.
  • Clean with a pH-neutral stone cleaner only. That means no vinegar, lemon, bleach, "all-purpose" sprays or scouring powders. Our dos and don'ts of cleaning stone tables goes into more detail.
  • Put felt pads under metal objects so they can't leave rust rings.
  • Use trivets for hot dishes and candles. Heat can drive oils and dyes deeper into the stone.
  • Rinse and dry vanities and basins daily. Toothpaste, soap and cosmetics are the most common causes of dull bathroom marble.

Nicola vanity in Persiano limestone, a stone bathroom vanity that should be rinsed and dried daily to prevent etching

Choose the right finish and stone for the room

Honed marble etches just as easily as polished marble, but you'll notice it far less, because there's no gloss to show a dull spot. That makes honed a smart choice for busy dining tables and kitchens. The trade-off is that honed stone is slightly more porous, so keep it sealed. Our guide to polished, honed and textured finishes compares the options.

If you'd rather not think about etching at all, look at harder, acid-resistant stones such as Patagonia quartzite.

Sienna Patagonia quartzite oval dining table on brushed brass legs, a harder stone that resists acid etching

Learning to love the patina

In much of Europe, a lightly etched marble table is a sign of a well-used family piece, not a fault. Over the years, small etches soften into an even, satin patina that many people come to love. If your stone is in daily use, it's worth deciding early whether you'll chase every mark or let it age gracefully.

When to call a professional

DIY is fine for faint marks. Get a stone restorer in when:

  • the etching covers a large area, like a whole tabletop, vanity top or bathtub rim
  • you can clearly feel the etch with a fingertip
  • the piece has a honed finish and you want an even, matte result
  • a stain has come back, or hasn't moved after three or four poultices
  • the mark is both etched and stained, and you're unsure what to treat first
  • the piece is onyx, or a rare or bookmatched stone you don't want to risk
  • there's a chip, crack or yellowing as well as the mark

Not sure what you're looking at? Send a clear photo, taken in daylight from a low angle, to our team and we'll help you work out what it is and what to do next.

 

Frequently asked questions

Is etching permanent?

The chemical change is, but the mark isn't. Etching can be removed by polishing or honing the surface back to an even finish.

Does sealing stop marble from etching?

No. A sealer slows liquids soaking into the pores, which helps with stains. Acid attacks the surface, so sealed marble still etches.

Why is there a white ring on my marble table?

Usually etching from an acidic drink, such as wine, juice or a cocktail. If it feels dull or rough when dry, it's an etch. If it's crusty and wipes or buffs away, it's a mineral deposit from water.

Will a poultice remove etching?

No. A poultice draws out something that has soaked into the stone. An etch is missing surface, so there's nothing to draw out.

Can I use vinegar or lemon to clean marble?

Never. Both are acids, and they'll etch the surface. Use a pH-neutral cleaner made for stone.

Does honed marble etch less than polished?

It etches just as easily, but the marks are much harder to see because there's no shine for them to dull.

Can I remove etching myself?

Light etching on polished marble often responds to a marble polishing powder. Deep, widespread or honed-finish etching is best left to a professional.

How long does a poultice take?

Usually 24 to 48 hours per application. Old or deep stains can need three or four rounds.

Is hydrogen peroxide safe on marble?

On white and light marble, yes, used in a poultice for organic stains. Avoid it on dark stones such as Nero Marquina or Verde Alpi, because it can lighten them.

Do travertine and onyx etch too?

Yes. Both are calcium-based like marble. Travertine's open holes can also trap liquid, and onyx is softer still, so treat both gently.

Is a marble table still worth it if it can etch?

For most people, yes. With coasters, a sealer and quick wipe-ups, most marks never happen, and the ones that do can be fixed. Browse our marble dining tables to find one that suits how you live.