The short answer
A solid stone bathtub weighs roughly 365 to 960 kg empty. Filled and in use, it can put well over a tonne onto a small patch of floor. A ground-floor concrete slab usually handles that easily. A timber floor, an upstairs bathroom or an apartment usually needs a structural engineer to check it first, and often some reinforcement.
That isn't a reason to rule out a stone bath. It's a reason to plan for one early, ideally before the bathroom is designed, rather than after the tub has been ordered.
This guide explains how much stone baths really weigh, how to work out the load on your floor, what different floor types can take, how timber floors are reinforced, and what to sort out for plumbing, waterproofing and delivery day.
How much does a stone bathtub weigh?
Solid stone baths are carved from a single block, so they weigh many times more than acrylic or cast-stone tubs. Our solid stone baths range from about 365 kg to 960 kg before any water goes in.
| Bath | Stone | Size | Empty weight |
|---|---|---|---|
| Statuarietto Solid Bath Tub | Statuarietto marble | 1800 mm long | 960 kg |
| Sculpt Oval Deep-Soak Bathtub | Romano travertine | 1700 × 750 × 460 mm | 670 kg |
| Carrara Round Bathtub | Carrara marble | 1350 mm across | 550 kg |
| Arabescato Bathtub | Arabescato marble | 1700 mm long | 525 kg |
| Portuguese Limestone Bathtub | Limestone | 1700 mm long | 490 kg |
| Roman Organic-Form Bathtub | Roman travertine | 1760 mm long | 365 kg |

Don't confuse solid stone with cast stone
Many baths sold as "stone" are actually cast stone: crushed stone or minerals bound with resin. They usually weigh around 100 to 200 kg. That's still heavy, but it's a very different job from installing a tub carved from solid marble or travertine. If you're comparing quotes, check which one you're being offered. Our guide to bathtub materials explains the differences.
Weight in use: add the water and the bather
The empty weight is only the start. Water weighs 1 kg per litre, and a freestanding bath typically holds 250 to 350 litres. Then add whoever is in it.
For example, our 525 kg Arabescato bath, filled with 300 litres of water and one 80 kg adult, puts about 905 kg on the floor. Our 960 kg Statuarietto bath, filled with 350 litres and one adult, puts about 1,390 kg on the floor.
Why that matters for your floor
Under the Australian loading standard (AS/NZS 1170.1), floors in a house are designed for an everyday load of about 1.5 kPa, or roughly 150 kg per square metre, spread evenly. Apartments are designed for about 2.0 kPa.
A filled stone bath puts its weight on a footprint of only about 1 to 1.5 square metres. In our Arabescato example, that's around 6.5 kPa, more than four times what a typical house floor is designed to carry in that spot. That's why a stone bath is treated as a special load, not just another piece of furniture.
Will your floor hold it?
It depends far more on the floor than on the bath. Here's how the common Australian floor types usually compare.
| Floor type | Usually suitable? | What to check |
|---|---|---|
| Concrete slab on the ground | Yes, in most homes | That the slab is sound and not cracked or sinking. Recessed or set-down slabs for wet areas are fine |
| Suspended concrete slab (upper floor of a house or apartment) | Often, with engineer approval | Slab thickness, span and what's above or below. Apartments also need strata approval |
| Timber floor on the ground floor (on piers or stumps) | Sometimes, often with reinforcement | Joist size, spacing and span, the condition of the stumps, and which way the joists run |
| Timber floor upstairs | Rarely without reinforcement | Joist size and span, what's below, and whether the bath sits mid-span or near a wall |
| Older homes and heritage terraces | Needs checking | Age and condition of the timber, any past termite or water damage, and earlier renovations |
Why "it held the old bath" doesn't count
A standard acrylic bath weighs around 30 to 50 kg empty, and a built-in bath spreads its load along the walls and framing. A freestanding stone bath can weigh ten to twenty times as much and sits on a small footprint in the middle of the room. A floor that has carried a shower, a vanity or an old bath for decades can still be the wrong floor for a stone bath.
Position matters
The same bath puts very different stress on a timber floor depending on where it sits. Near a load-bearing wall, or right above a beam or bearer, the load travels almost straight down. In the middle of a long joist span, the joists have to bend to carry it. If you have a choice, ask your engineer which position in the room works best.

When you need a structural engineer
Get an engineer to check the floor before you buy if any of these apply:
- the bathroom has a timber floor, upstairs or down
- it's on an upper level of a house or in an apartment
- the house is old, or you're unsure what the floor is made of
- the bath weighs more than about 400 kg empty
- you're planning other heavy items nearby, such as a stone vanity or large-format stone tiles
An engineer's inspection is a small cost compared with the price of the bath, and many builders and certifiers will ask for one anyway. Give them the bath's empty weight, its water capacity, its footprint and where you'd like it to sit.
How timber floors are reinforced
Most timber floors can be made strong enough for a stone bath. Your engineer will specify exactly what's needed, but these are the usual options, from simplest to most involved.
- Sistering joists. New joists are bolted or glued alongside the existing ones under the bath, roughly doubling their strength.
- Adding blocking. Short pieces of timber fixed between joists make them share the load, so no single joist carries the bath alone.
- Adding a bearer or beam underneath. A new beam, sometimes engineered timber or steel, is run under the joists to shorten their span. On a ground floor it usually sits on new piers or stumps.
- Thickening the floor sheet. A heavier structural sheet over the joists helps spread the load. It's usually combined with one of the options above, not used on its own.
- A concrete pad. On a ground-floor timber floor with good access underneath, part of the floor can be replaced with a small reinforced concrete pad under the bath. It's the most work, but it takes the load straight to the ground.

Access makes a big difference to cost. Reinforcing from underneath, through a subfloor or a ceiling below, is usually much cheaper than lifting a finished bathroom floor. That's why the best time to plan for a stone bath is before the bathroom is tiled.
Apartments and strata
In an apartment, the floor slab is usually common property. Any work that touches it, including core-drilling for a floor waste, normally needs approval from the owners corporation, and often a report from their engineer. Check your strata by-laws and start that process early, because approvals can take weeks.
Plumbing, drainage and waterproofing
Once a solid stone bath is in place, lifting it again is a major job. So everything underneath it has to be right the first time.
- Get the spec sheet before the rough-in. Waste position, waste size and the exact footprint vary from bath to bath, and between hand-carved pieces. Your plumber needs these measurements before the floor is screeded or tiled.
- Check for an overflow. Many solid stone baths don't have one. That's normal, but it affects which waste fitting your plumber uses, and it means you shouldn't leave a running bath unattended.
- Plan for servicing. Choose a waste that can be cleared and serviced from inside the bath, so a blocked drain never means moving half a tonne of stone.
- Decide on tapware early. A floor-mounted bath filler needs its pipes set into the floor before tiling. A wall-mounted spout needs to reach far enough to clear the rim.
- Waterproof properly. Bathrooms in Australia must be waterproofed to the wet-area standard (AS 3740). Make sure the membrane runs under the bath's whole footprint and is sealed around the waste. Water trapped under a heavy tub can quietly damage a timber floor for years.
- Use licensed trades. Plumbing and waterproofing must be done by appropriately licensed trades in Australia. Keep their certificates. You may need them for insurance or when you sell.

For keeping the stone itself in good condition once it's in, read our guide to caring for your marble bathtub.
Delivery, access and installation day
Getting the bath into the room is often harder than holding it up. Measure the whole route from the truck to the bathroom before you order.
- Doors and corridors. Check every doorway, hallway and turn against the bath's packed dimensions, not just its finished size. Crates add several centimetres.
- Stairs. A 500 kg-plus bath can't simply be carried upstairs. It may need a stair-climbing trolley, a temporary ramp or a crane over a balcony or through a window.
- Lifts. In an apartment, check the lift's weight limit and internal size, and book it through building management.
- Floors along the way. Protect finished floors, and make sure suspended floors on the route can take the bath and the people moving it.
- Crew and equipment. Expect a specialist crew with suitable lifting gear. A bath this heavy isn't a two-person job.
- Levelling. Once it's in position, the bath is levelled carefully so it drains properly and sits evenly. Uneven support can stress the stone over time.

If you're a builder, designer or architect specifying a stone bath for a project, talk to us through our Trade page. We can share specifications early, so the structure and plumbing are designed around the bath from the start.
Your stone bath checklist
Work through this before you order:
- Find out the bath's empty weight, water capacity, footprint and waste position.
- Work out the full weight: bath, plus water at 1 kg per litre, plus the bather.
- Identify your floor type: concrete slab, suspended slab, or timber, and which level it's on.
- Get a structural engineer to check the floor for anything other than a ground-floor slab.
- In an apartment, check the strata by-laws and apply for approval.
- Agree any reinforcement with your builder before the bathroom is tiled.
- Give your plumber the spec sheet before the rough-in, and confirm the waste, overflow and tapware.
- Make sure the waterproofing covers the bath's full footprint.
- Measure the delivery route, and book any lifts, cranes or specialist movers.
Browse our marble bathtubs to compare sizes and weights, or read how much a marble bathtub costs in Australia to budget for the bath and its installation.
Frequently asked questions
How much does a marble bathtub weigh?
A solid marble bath usually weighs between about 400 and 1,000 kg empty, depending on its size and shape. Ours range from 365 kg to 960 kg.
How much does a stone bath weigh when it's full?
Add 1 kg for every litre of water, plus the bather. A 525 kg bath holding 300 litres, with one adult in it, puts about 905 kg on the floor.
Can I put a stone bath upstairs?
Often, yes, but almost always with a structural engineer's check first, and usually some reinforcement on a timber floor.
Can I put a stone bath in an apartment?
Many apartments have concrete slabs that can take one, but you'll need approval from the owners corporation, and often an engineer's report. Check access too: the lift, corridors and doorways.
Do I need an engineer for a stone bath on a concrete slab?
On a sound ground-floor slab, usually not. For a suspended slab, an upper floor or anything you're unsure about, yes.
Can I reinforce my floor after the bathroom is finished?
Sometimes, if there's access from underneath. Otherwise the floor may need to be lifted, so it's much easier to plan reinforcement before tiling.
Are cast-stone baths lighter?
Yes. Cast-stone baths are made from crushed stone and resin, and usually weigh around 100 to 200 kg. Solid stone baths are carved from a single block and are much heavier.
Do stone baths have an overflow?
Many solid stone baths don't. Check the spec sheet before the plumbing rough-in, so your plumber can choose the right waste.
Can I install a stone bath myself?
We don't recommend it. Moving, positioning and levelling a solid stone bath takes a specialist crew, and plumbing and waterproofing must be done by licensed trades.
Why choose a stone bath if it's this heavy?
That same mass holds heat far longer than acrylic, so the water stays warm through a long soak. A solid stone bath is also built to last for generations, so the planning pays off.
Have a question about a specific bath and your floor? Contact our team with the bath you're considering and a photo or plan of your bathroom.

